Rekeying and Lock Changes in Minneapolis
New pins for the locks you already have, so old keys stop working, or new locks and deadbolts where the old ones are worn, broken or weak.
There are two ways to change who can open a door. Rekeying keeps the lock and changes the pins in its cylinder, so a new key turns it and the old ones stop. Replacing the lock changes the hardware itself. The state of the lock, and what you want from it, decides which one fits.
Rekeying between tenants is common work for landlords in the area’s apartment buildings, and it is the usual first step after moving into a home whose old keys nobody can account for.
| Option | What changes | Good when |
|---|---|---|
| Rekey | New pins in the cylinder and a new key; the lock stays | The lock works well and only the keys need to change |
| Replace lock | The whole lockset or deadbolt, its keys and often its look | The lock is worn, broken or weak, or another style or keyway is wanted |
| Add deadbolt | A bore in the door, a bolt in its edge, a strike in the frame | The door has only a knob or lever with a spring latch |
| Match keys across doors | Each cylinder pinned to the cuts of one key | Several doors take the same key blank and should open with one key |
Pins, Plug and Shear Line
A pin tumbler cylinder is a plug that turns inside a shell. Stacks of small pins cross the line between the two: a key pin that the key touches, a driver pin over it, a spring on top. With no key in, the driver pins straddle that line and hold the plug still. The right key lifts each stack until the gap between its pins sits exactly at the shear line, and the plug turns.
Rekeying swaps the key pins. With the cylinder off the door, the plug is turned with the working key and slid out behind a follower that holds the driver pins and springs in the shell. The old key pins are tipped out and new ones, each matched to a cut on the new key, go in. The plug goes back, the new key is tried, then the old one, which should no longer turn it.
Because the plug has to turn before it comes out, rekeying is simplest with a working key for each lock. Without one, the cylinder is picked first or the lock is replaced.
Good Times to Rekey
- A new home. Earlier owners, their relatives, cleaners and contractors may still hold keys, and nobody can count them.
- An ended tenancy. Keys handed back prove little when copies are easy to cut; new pins before the next tenant moves in settle it.
- Lost keys. A ring lost with an address tag, a car registration or a piece of mail points straight to the door it opens.
- A former employee. Returned keys may not be the only copies, and rekeying the doors they opened closes the question.
When a lost ring could lead someone to your door, call (612) 662-1116 rather than waiting for a convenient day.
Worn, Broken or Weak Hardware
Rekeying cannot fix a lock that is failing. A worn lock shows it: a key that has to be jiggled before it turns, a drooping lever, a latch that no longer springs all the way out. A broken one shows it plainly: a cam that spins without moving the bolt, a cracked housing, a handle that turns and does nothing else.
Weak hardware is harder to spot. A light knob lock on an outside door, or a strike held by short screws in a thin jamb, gives way to a kick long before the bolt does. A sturdier lock helps, and so do long screws that carry the strike into the framing behind the jamb.
A new lock is also the way to a different look, levers in place of knobs, or a restricted keyway whose blanks are controlled, so copies cannot be cut at any key counter.
Is rekeying as secure as a new lock?
Against the old keys, yes: once the pins change, a key cut for the old combination no longer turns the plug, whoever holds it.
Rekeying does not make the lock any harder to pick, drill or force, since the cylinder, the bolt and the strike stay as they were. A light or worn lock stays light or worn, and there a new lock is the stronger choice.
When does a lock need replacing instead of rekeying?
When the lock itself is the problem rather than the keys: worn until the key sticks or turns only at one angle, broken inside, cracked, or too light for the door it guards. Rekeying changes only the pins, so it cannot help any of those. A keypad or smart lock in place of the old one is a replacement too.
Fitting a New Deadbolt
A door held only by a knob or lever relies on a spring latch, and a spring latch can be eased back. A deadbolt adds a solid bolt that moves only by key or thumb turn. Fitting one where there was none means boring the door, usually a 2-1/8 inch hole through the face and a 1-inch hole from the edge for the bolt, then a matching hole and a strike in the frame.
A boring jig clamped to the door keeps the two holes square, so the bolt slides without rubbing. The strike goes where the bolt actually meets the frame, and with the door shut the bolt should throw its full length without a push or a pull.
Every deadbolt raises one choice: a thumb turn inside, or a key on both sides. A double-cylinder deadbolt stops a hand reaching through nearby glass, but a key is then needed to get out, and building codes generally expect the main door of a home to open from inside without one.
One Key for Several Doors
The front door, the back door and the garage entry can usually work from one key, which locksmiths call keying alike. The locks need the same key blank, which in practice means the same keyway; a lock of another make may need a new cylinder, or a new lock, before it can join the rest.
In a small building the same pinning becomes a master key system, with a change key for each unit and a master key that opens them all, part of the work on business locks.
Can every door in the house work with one key?
Usually, as long as the locks take the same key blank. Locks of one make, or of makes that use the same keyway, can all be pinned to one key; a lock with a different keyway needs a new cylinder or a new lock to match. The backup cylinder on a keypad or smart lock may or may not take the house key’s blank, and the threaded cylinder of an older mortise lock can usually be exchanged for a matching one.
Counting Doors, Locks and Keys
A rekey or lock change starts from a plain count: the outside doors, the keyed locks on each, a working key for every lock, and which doors should end up on one key. Landlords can add the unit numbers and whether the building’s entry door is part of the job.
Send that list through Schedule an Estimate, with photos of the locks by email if they are easy to take.